Questions tagged [transient]
A change in an electrical system from an equilibrium or steady state. The response of the electrical system to a transient is its transient response. Examples of transients include load transients (in which the load suddenly changes) and line transients (in which the input voltage of an electrical system suddenly changes). The electrical system may require protection from certain transients, e.g. by using transient-voltage-suppression (TVS) diodes.
414 questions
1
vote
0
answers
33
views
Elmore delay equivalent for delay calculation
I am trying to understand the concept of Elmore delay calculating delay factor of the CMOS circuitries using RC approximation.
According to CMOS VLSI Design : A Circuits and Systems Perspective ...
- 345
2
votes
1
answer
146
views
Understand mismatch between small signal ac amplitude and transient amplitude (after transient behavior has gone) [duplicate]
I have the following circuit with only passive elements:
I have an explicit resistance of 1k Ohm in series with the voltage source, which is specified to have an amplitude of 1 V for both the ...
- 312
0
votes
0
answers
138
views
Current and capacitor voltage calculation with IC in Razavi's book
I started to read "Design of Analog CMOS Integrated Circuits", Second Edition, by Behzad Razavi and found this circuit in chapter 2 ("Basic MOS Device Physics") question 2.10a, ...
- 39
1
vote
0
answers
61
views
Clearance calculation according to IEC 61010-1 section K.3.2
I'm designing a circuit which has to meet the standard IEC 61010-1. It has a transient voltage limitation at the input, so I can calculate my clearances according to section K.3.2.
The surge ...
- 124
3
votes
4
answers
1k
views
Why isn't inductor current remaining same in the following circuit at time t=0?
I am trying to understand inductor behaviour, specifically boosting action provided by them by means of the following circuit.
Initially switch SW2 is closed and SW1 is open.
I expect inductor ...
0
votes
1
answer
46
views
How will the voltage across the series capacitor vary?
At t=0, due to the infinite frequency of the step, the network will reduce to a series to 2 capacitors and both will get charged. The capacitor to the left of X has a polarity such that it gets ...
- 63
2
votes
3
answers
396
views
Short circuit behavior for a capacitor and voltage source in series
From Alexander Sadiku's Fundamentals of Electric Circuits, Example 8.2:
My current intuition of circuits tells me that any short circuit across the terminals of a circuit element, in essence, removes ...
- 334
2
votes
3
answers
156
views
When simulating the open loop gain of an oscillator in LTspice, what to use as output load?
I have an LTspice circuit of a Colpitts oscillator with an common emitter amplifier:
I'm using dual value resistors (R6 and R7) so that the circuit is a closed loop in transient and DC simulation and ...
- 312
0
votes
2
answers
167
views
Transient Circuit Problem
This is my correct solution for this question, however it asked me to sketch a waveform for iL(t). If so, how can I show its initial values, Is and common characteristics?
3
votes
3
answers
182
views
How to find current in this RL circuit?
I could easily solve for Ix and I in the inductor. Still, when the switch is opened and discharging occurs, I don't understand how I can model a differential equation to get the current in the ...
- 75
1
vote
2
answers
126
views
What happens if I connect R1 to this circuit when the power is on
Figure from here
I’m curious about the effects of connecting the resistor (R1) to this circuit that’s already powered on. I’ve heard warnings about plugging or unplugging components while the circuit ...
- 777
0
votes
0
answers
64
views
ADC reference voltage ringing: real or probe artifact?
I'm debugging an ADC chip and suspect one of the reference voltages might be unstable. To investigate, I connected a passive oscilloscope probe to the reference voltage header. This node is decoupled ...
- 777
2
votes
1
answer
132
views
How to select a switching regulator, output capacitor and inductor, to handle an output transient peak current with a given input voltage?
I'm designing a circuit that contains a switching regulator that will need to cope with a transient peak current of around 700-800 mA at startup time. I don't know how long this transient exactly ...
- 1,463
0
votes
0
answers
62
views
Issue with SPDT Switch in ADS 2015 Transient Simulation
I'm working with ADS 2015, and I have an issue with the SPDT switch not working correctly in transient simulation. My circuit consists of:
A sinusoidal input signal (VSine)
A SPDT switch controlled by ...
0
votes
3
answers
111
views
Achieving High Slew Rate in Load Transient Testing for DC-DC Converters
I am performing load transient testing on several DC-DC converters using my Keysight EL34243 electronic load. However, I am unable to achieve the specified slew rate seen in the datasheet graphs. The ...
