Questions tagged [driver]
A chip or a circuit that sends a signal with more current or voltage, or over longer distances.
1,046 questions
2
votes
2
answers
171
views
Mystery 6-pin IC in a 30 watt LED bulb
Can anyone identify this IC?
I was trying to repair a high power 30 watt LED bulb. I encountered this mystery 6-pin IC which I tried very hard to identify. Just has 'G31H' in the first line and '9L30' ...
- 21
3
votes
1
answer
63
views
A6217 with 700 mA LED schematic check
I’m working on a circuit board for an amber strobe unit. It will feature eight individually addressable LEDs controlled by an ATtiny microcontroller. Each 700 mA LED will be driven by an A6217 driver ...
1
vote
3
answers
199
views
A real working driver is needed for signal from 74AC14 to voltage multiplier
A real working driver is require to drive a capacitor voltage multiplier, using 5 x 74AC14 as gate rivers, 5V in, 12V out.
Supply 5 Volts from 278R05.
One section of the74AC14 is used as an ...
- 39
-1
votes
0
answers
75
views
Circuit for Piezo atomizer
currently I am working on making piezo actuator/humidifier that can be controlled by 9 digital pins of STM32 (3.3V logic).
According to the provided detail, the resonance frequency of the piezo ...
- 19
-1
votes
1
answer
78
views
Ethernet driver Pulse HX1188NL 1522-PP pin names
I want to get Ethernet driver pin names, but in datasheet was missed some pins. Certainly, was missed pins under numbers 4, 5, 12, 13.
Ethernet driver schematic picture: Datasheet
- 363
0
votes
1
answer
149
views
I have a PWM signal that I want to control a heater (3 ohms) with a 36V source. My MOSFETS keep blowing using TC4427
I initially used a 74HC04 to drive the MOSFET gates. This was initially because I wanted 5V on the gate: by putting the pwm 3v3 through the 74HC04 and then re-inverting the pwm came out st 5V. I chose ...
- 387
1
vote
1
answer
111
views
Understanding LED driver load/overload behaviour
Let's say I have 15 m of LED strip at 4.8 W/m, that makes 72 W of load. I already know that in practice I will always have these LEDs dimmed at below 30%, and there is no way I will ever want to use ...
- 121
0
votes
0
answers
61
views
BTS7960 Motor driver
I'm trying to drive this 24v motor with a BTS7960,and two pedals for acceleration and braking
The code works fine and I tested the output from the driver, gave a full output of 26.4v on acceleration ...
- 11
1
vote
1
answer
96
views
Questions Regarding PCB wiring from Schematic Design
H-Gate Driver in use: [https://lcsc.com/product-detail/Gate-Drivers_Infineon-IR2101STRPBF_C2956.html]
The general issue is connecting components in general on a PCB and if specific tracing is needed ...
- 19
0
votes
1
answer
77
views
Designing Gate Driver for Cascode GaN HEMT (GAN111-650WSB)
I am new to designing a gate driver for WBG devices. I want to seek your opinion as to why there is a overshoot in my gate voltage of my high-side GaN HEMT from second switching cycle onwards. ...
- 11
1
vote
1
answer
77
views
Can one use a 32mA line driver with a source-series-terminated 50ohm transmission line and 3.3v VCC?
It appears that line drivers generally do not exceed 32mA of drive ability, at least not in the "recommended operating conditions" section.
At 3.3V VCC [to the driver chip, and hence signal ...
- 557
0
votes
0
answers
60
views
Peltier driver with 12V 25A
I am looking for a way to control Peltier elements, both for heating and cooling.
The technical requirements are.
Control via Raspberry Pi Pico (3.3V) can PWM 7 Hz to 125 MHz.
4X Peltier element TEC1-...
1
vote
2
answers
75
views
Using a MDDRC10 driver with a Raspberry Pi Pico
I want to use a MDDRC10 motor driver with a Raspberry Pi Pico. But I can't get it to work from the manual. As I understand it from page 3, anything over 1.5 V will activate the channel and then I can ...
- 349
4
votes
2
answers
382
views
Piezo buzzer drivers with different sound pressure
I usually drive a piezo buzzer with the common driving circuit: a MOS (or NPN) and a resistor across the buzzer (between VCC and drain). The gate is driven by a MCU with a square wave.
The pressure ...
- 171
6
votes
3
answers
504
views
Can I have too many vias to stitch planes together?
I am currently designing a stepper motor driver and have oriented my design on the eval board from the tmc5160. I need lots of vias to provide low inductive paths, as well as stitching for reducing ...
- 85