someone accused me of feigning a sexual attraction to spiders for clout. there's easier ways to get clout, man.....
Someone once called my 22 minute hand sewn 18th century buttonhole tutorial video “Empty, clout driven content” so I think some people will just say anything.
Edit: Should have added a link (even though that’s apparently clout-chasing) here it is!
See more posts like this on Tumblr
#sewing #internet #buttonholesmeraxes-of-new-albion asked:
Any tips on learning to make buttonholes? I've been putting it off for.... *checks notes* like three years.... but better late than never and all that. I don't have any fancy machines so I gotta do it by hand but that seems right up your alley.
Thanks!
vinceaddams answered:
It IS up my alley, yes, I do most of my buttonholes by hand!
I’m actually part way through filming an 18th century buttonhole tutorial, but I expect it’ll be a few more weeks before I finish that and put it on the youtubes, so in the meantime here’s the very very short version. (The long version is looking like it’ll probably be about 40 minutes maybe, judging by how much script I’ve written compared to my last video?)
Mark your line, a bit longer than your button is wide. I usually use a graphite mechanical pencil on light fabrics, and a light coloured pencil crayon on dark ones. (I have fabric pencils too, but they’re much softer and leave a thicker line.)
You may want to baste the layers together around all the marked buttonholes if you’re working on something big and the layers are shifty and slippery. I’m not basting here because this is just a pants placket.
Do a little running stitch (or perhaps a running backstitch) in fine thread around the line at the width you want the finished buttonhole to be. This holds the layers of fabric together and acts as a nice little guide for when you do the buttonhole stitches.
Cut along the marked line using a buttonhole cutter, or a woodworking chisel. Glossy magazines are the best surface to put underneath your work as you push down, and you can give it a little tap with a rubber mallet if it’s not going through all the way.
I’m aware that there are some people who cut their buttonholes open using seam rippers, and if any of them are reading this please know that that is abhorrent behaviour and I need you to stop it immediately. Stop it.
Go get a buttonhole cutter for 10 bucks and your life will be better for it. Or go to the nearest hardware store and get a little woodworking chisel. This includes machine buttonholes, use the buttonhole cutter on them too. If you continue to cut open buttonholes with a seam ripper after reading this you are personally responsible for at least 3 of the grey hairs on my head.
Do a whipstitch around the cut edges, to help prevent fraying while you work and to keep all those threads out of the way. (For my everyday shirts I usually do a machine buttonhole instead of this step, and then just hand stitch over it, because it’s a bit faster and a lot sturdier on the thin fabrics.)
I like to mark out my button locations at this point, because I can mark them through the holes without the buttonhole stitches getting in the way.
For the actual buttonhole stitches it’s really nice if you have silk buttonhole twist, but I usually use those little balls of DMC cotton pearl/perle because it’s cheap and a good weight. NOT stranded embroidery floss, no separate strands! It’s got to be one smooth twisted thing!
Here’s a comparison pic between silk buttonhole twist (left) and cotton pearl (right). Both can make nice looking buttonholes, but the silk is a bit nicer to work with and the knots line up more smoothly.
I’ve actually only used the silk for one garment ever, but am going to try to do it more often on my nicer things. I find the cotton holds up well enough to daily wear though, despite being not ideal. The buttonholes are never the first part of my garments to wear out.
I cut a piece of about one arm’s length more or less, depending on the size of buttonhole. For any hole longer than about 4cm I use 2 threads, one to do each side, because the end gets very frayed and scruffy by the time you’ve put it through the fabric that many times.
I wax about 2cm of the tip (Not the entire thread. I wax the outlining/overcasting thread but not the buttonhole thread itself.) to make it stick in the fabric better when I start off the thread.
I don’t tend to tie it, I just do a couple of stabstitches or backstitches and it holds well. (I’m generally very thorough with tying off my threads when it comes to hand sewing, but a buttonhole is basically a long row of knots, so it’s pretty sturdy.)
Put the needle through underneath, with the tip coming up right along that little outline you sewed earlier. And I personally like to take the ends that are already in my hand and wrap them around the tip of the needle like so, but a lot of people loop the other end up around the other way, so here’s a link to a buttonhole video with that method. Try both and see which one you prefer, the resulting knot is the same either way.
Sometimes I can pull the thread from the end near the needle and have the stitch look nice, but often I grab it closer to the base and give it a little wiggle to nestle it into place. This is more necessary with the cotton than it is with the silk.
The knot should be on top of the cut edge of the fabric, not in front of it.
You can put your stitches further apart than I do if you want, they’ll still work if they’ve got little gaps in between them.
Keep going up that edge and when you get to the end you can either flip immediately to the other side and start back down again, or you can do a bar tack. (You can also fan out the stitches around the end if you want, but I don’t like to anymore because I think the rectangular ends look nicer.)
Here’s a bar tack vs. no bar tack sample. They just make it look more sharp, and they reinforce the ends.
For a bar tack do a few long stitches across the entire end.
And then do buttonhole stitches on top of those long stitches. I also like to snag a tiny bit of the fabric underneath.
Then stick the needle down into the fabric right where you ended that last stitch on the corner of the bar tack, so you don’t pull that corner out of shape, and then just go back to making buttonhole stitches down the other side.
Then do the second bar tack once you get back to the end.
To finish off my thread I make it sticky with a bit more beeswax, waxing it as close to the fabric as I can get, and then bring it through to the back and pull it underneath the stitches down one side and trim it off.
In my experience it stays put perfectly well this way without tying it off.
Voila! An beautiful buttonholes!
If you want keyhole ones you can clip or punch a little rounded bit at one end of the cut and fan your stitches out around that and only do the bar tack at one end, like I did on my 1830’s dressing gown.
(I won’t do that style in my video though, because they’re not 18th century.)
Do samples before doing them on a garment! Do as many practice ones as you need to, it takes a while for them to get good! Mine did not look this nice 10 years ago.
Your first one will probably look pretty bad, but your hundredth will be much better!
Edit: Video finished!
And here’s the blog post, which is mostly a slightly longer version of this post.
#no to seam ripper?????? #my sewing machine manual says to use the seam ripper!
The manual on my newly acquired Pfaff says so too, but it’s WRONG!!
“Be careful not to injure the bartacks” well you wouldn’t have to worry about that if you got a buttonhole cutter and pushed straight down!
Or get a pair buttonhole scissors! They exist!
Someone in the comments suggested putting a pin across the end to prevent cutting past the buttonhole with the seam ripper, and yeah that would stop it, but it would also dull your seam ripper way faster and then your cut edges will be even more ragged and shitty.
Made my first handsewn buttonhole thanks to @vincentbriggs tutorial. Thank you Vincent for the very helpful and informative post. I had no clue where to even begin and I was stuck on my project until your tutorial came along.
It's not as pretty as it could be and I don't truly understand how to do the bar tacks yet, but I'm still quite proud. Now I have seven more buttonholes to do and I don't feel quite so daunted to take on the task.
I highly recommend anyone hesitating to tackle buttonholes to give it a watch/read.
https://www.tumblr.com/vincentbriggs/733919413021114368/finished-my-buttonhole-tutorial-video-its-22
YAY! For a first buttonhole, it’s absolutely fantastic!! I’m so glad my tutorial was helpful!
The 1730′s coat is done!
(It’ll be a while before I get Nice Fancy Photos of it, because I still need to make 1730′s breeches, and a waistcoat that’s long enough and actually fits me properly. And I’ll need to borrow a camera that doesn’t have a big dust speck trapped in the lens.)
OMG I’m loving that profile silhouette!!! And the buttons! AND THE GIGANTIC CUFFS!
Can’t wait for the entire outfit u.u
@vincents-crows just being gorgeous, as usual.
Thank you! I’ve just added up the time sheet and it came to a grand total of 100 hours and 33 minutes. Wow. This is one of the most time consuming things I’ve ever made. Of that time, 39:56 of it was spent on the 79 buttonholes, and 7:32 on the 47 buttons. Only 6 of these buttons are functional.
meraxes-of-new-albion asked:
Any tips on learning to make buttonholes? I've been putting it off for.... *checks notes* like three years.... but better late than never and all that. I don't have any fancy machines so I gotta do it by hand but that seems right up your alley.
Thanks!
vinceaddams answered:
It IS up my alley, yes, I do most of my buttonholes by hand!
I’m actually part way through filming an 18th century buttonhole tutorial, but I expect it’ll be a few more weeks before I finish that and put it on the youtubes, so in the meantime here’s the very very short version. (The long version is looking like it’ll probably be about 40 minutes maybe, judging by how much script I’ve written compared to my last video?)
Mark your line, a bit longer than your button is wide. I usually use a graphite mechanical pencil on light fabrics, and a light coloured pencil crayon on dark ones. (I have fabric pencils too, but they’re much softer and leave a thicker line.)
You may want to baste the layers together around all the marked buttonholes if you’re working on something big and the layers are shifty and slippery. I’m not basting here because this is just a pants placket.
Do a little running stitch (or perhaps a running backstitch) in fine thread around the line at the width you want the finished buttonhole to be. This holds the layers of fabric together and acts as a nice little guide for when you do the buttonhole stitches.
Cut along the marked line using a buttonhole cutter, or a woodworking chisel. Glossy magazines are the best surface to put underneath your work as you push down, and you can give it a little tap with a rubber mallet if it’s not going through all the way.
I’m aware that there are some people who cut their buttonholes open using seam rippers, and if any of them are reading this please know that that is abhorrent behaviour and I need you to stop it immediately. Stop it.
Go get a buttonhole cutter for 10 bucks and your life will be better for it. Or go to the nearest hardware store and get a little woodworking chisel. This includes machine buttonholes, use the buttonhole cutter on them too. If you continue to cut open buttonholes with a seam ripper after reading this you are personally responsible for at least 3 of the grey hairs on my head.
Do a whipstitch around the cut edges, to help prevent fraying while you work and to keep all those threads out of the way. (For my everyday shirts I usually do a machine buttonhole instead of this step, and then just hand stitch over it, because it’s a bit faster and a lot sturdier on the thin fabrics.)
I like to mark out my button locations at this point, because I can mark them through the holes without the buttonhole stitches getting in the way.
For the actual buttonhole stitches it’s really nice if you have silk buttonhole twist, but I usually use those little balls of DMC cotton pearl/perle because it’s cheap and a good weight. NOT stranded embroidery floss, no separate strands! It’s got to be one smooth twisted thing!
Here’s a comparison pic between silk buttonhole twist (left) and cotton pearl (right). Both can make nice looking buttonholes, but the silk is a bit nicer to work with and the knots line up more smoothly.
I’ve actually only used the silk for one garment ever, but am going to try to do it more often on my nicer things. I find the cotton holds up well enough to daily wear though, despite being not ideal. The buttonholes are never the first part of my garments to wear out.
I cut a piece of about one arm’s length more or less, depending on the size of buttonhole. For any hole longer than about 4cm I use 2 threads, one to do each side, because the end gets very frayed and scruffy by the time you’ve put it through the fabric that many times.
I wax about 2cm of the tip (Not the entire thread. I wax the outlining/overcasting thread but not the buttonhole thread itself.) to make it stick in the fabric better when I start off the thread.
I don’t tend to tie it, I just do a couple of stabstitches or backstitches and it holds well. (I’m generally very thorough with tying off my threads when it comes to hand sewing, but a buttonhole is basically a long row of knots, so it’s pretty sturdy.)
Put the needle through underneath, with the tip coming up right along that little outline you sewed earlier. And I personally like to take the ends that are already in my hand and wrap them around the tip of the needle like so, but a lot of people loop the other end up around the other way, so here’s a link to a buttonhole video with that method. Try both and see which one you prefer, the resulting knot is the same either way.
Sometimes I can pull the thread from the end near the needle and have the stitch look nice, but often I grab it closer to the base and give it a little wiggle to nestle it into place. This is more necessary with the cotton than it is with the silk.
The knot should be on top of the cut edge of the fabric, not in front of it.
You can put your stitches further apart than I do if you want, they’ll still work if they’ve got little gaps in between them.
Keep going up that edge and when you get to the end you can either flip immediately to the other side and start back down again, or you can do a bar tack. (You can also fan out the stitches around the end if you want, but I don’t like to anymore because I think the rectangular ends look nicer.)
Here’s a bar tack vs. no bar tack sample. They just make it look more sharp, and they reinforce the ends.
For a bar tack do a few long stitches across the entire end.
And then do buttonhole stitches on top of those long stitches. I also like to snag a tiny bit of the fabric underneath.
Then stick the needle down into the fabric right where you ended that last stitch on the corner of the bar tack, so you don’t pull that corner out of shape, and then just go back to making buttonhole stitches down the other side.
Then do the second bar tack once you get back to the end.
To finish off my thread I make it sticky with a bit more beeswax, waxing it as close to the fabric as I can get, and then bring it through to the back and pull it underneath the stitches down one side and trim it off.
In my experience it stays put perfectly well this way without tying it off.
Voila! An beautiful buttonholes!
If you want keyhole ones you can clip or punch a little rounded bit at one end of the cut and fan your stitches out around that and only do the bar tack at one end, like I did on my 1830’s dressing gown.
(I won’t do that style in my video though, because they’re not 18th century.)
Do samples before doing them on a garment! Do as many practice ones as you need to, it takes a while for them to get good! Mine did not look this nice 10 years ago.
Your first one will probably look pretty bad, but your hundredth will be much better!
Finished the video! I cover a lot more things in it - measuring & marking, decorative false buttonholes, half open ones, and a couple of 18th century methods for lining them. (Accompanying blog post here.)
At 22 minutes it's shorter than I expected, there are a lot fewer gaps in between the talking than there were in my previous video.
The version without the video is getting a lot of notes, so I’m reblogging the one with the video again!
Also, my sewing/other art blog is @vincentbriggs
@mxbuster replied to your post “Any tips on learning to make buttonholes? I’ve…”:
Wait, Vince, can you take a picture of how to use the scissors? What’s the screw thing for? How do I cut the buttonhole with it?
Yes, sorry for the delay!
They work like this! The gap behind the blades leaves room for the edge of the garment, though it’s still a bit small for some larger things like coats, and not really much help for vertical buttonholes.
The screw thing is so that you can adjust them so that they don’t close all the way, which is useful if you have very short buttonholes. The one on mine is pretty worn and a little bent, but it’s not completely stripped yet, so it still works.
These ones aren’t as dull as they look, but I really ought to get them sharpened & cleaned up at some point.
Mine came from my Grandma and I don’t know exactly how old they are, but there are some very similar looking ones in the 1897 Sears catalogue.
It’s 1 am and I should be sleeping BUT I ONLY HAVE 3 BUTTONHOLES LEFT TO DO! (The topmost one and the two closest to the bottom)
meraxes-of-new-albion asked:
Any tips on learning to make buttonholes? I've been putting it off for.... *checks notes* like three years.... but better late than never and all that. I don't have any fancy machines so I gotta do it by hand but that seems right up your alley.
Thanks!
vinceaddams answered:
It IS up my alley, yes, I do most of my buttonholes by hand!
I’m actually part way through filming an 18th century buttonhole tutorial, but I expect it’ll be a few more weeks before I finish that and put it on the youtubes, so in the meantime here’s the very very short version. (The long version is looking like it’ll probably be about 40 minutes maybe, judging by how much script I’ve written compared to my last video?)
Mark your line, a bit longer than your button is wide. I usually use a graphite mechanical pencil on light fabrics, and a light coloured pencil crayon on dark ones. (I have fabric pencils too, but they’re much softer and leave a thicker line.)
You may want to baste the layers together around all the marked buttonholes if you’re working on something big and the layers are shifty and slippery. I’m not basting here because this is just a pants placket.
Do a little running stitch (or perhaps a running backstitch) in fine thread around the line at the width you want the finished buttonhole to be. This holds the layers of fabric together and acts as a nice little guide for when you do the buttonhole stitches.
Cut along the marked line using a buttonhole cutter, or a woodworking chisel. Glossy magazines are the best surface to put underneath your work as you push down, and you can give it a little tap with a rubber mallet if it’s not going through all the way.
I’m aware that there are some people who cut their buttonholes open using seam rippers, and if any of them are reading this please know that that is abhorrent behaviour and I need you to stop it immediately. Stop it.
Go get a buttonhole cutter for 10 bucks and your life will be better for it. Or go to the nearest hardware store and get a little woodworking chisel. This includes machine buttonholes, use the buttonhole cutter on them too. If you continue to cut open buttonholes with a seam ripper after reading this you are personally responsible for at least 3 of the grey hairs on my head.
Do a whipstitch around the cut edges, to help prevent fraying while you work and to keep all those threads out of the way. (For my everyday shirts I usually do a machine buttonhole instead of this step, and then just hand stitch over it, because it’s a bit faster and a lot sturdier on the thin fabrics.)
I like to mark out my button locations at this point, because I can mark them through the holes without the buttonhole stitches getting in the way.
For the actual buttonhole stitches it’s really nice if you have silk buttonhole twist, but I usually use those little balls of DMC cotton pearl/perle because it’s cheap and a good weight. NOT stranded embroidery floss, no separate strands! It’s got to be one smooth twisted thing!
Here’s a comparison pic between silk buttonhole twist (left) and cotton pearl (right). Both can make nice looking buttonholes, but the silk is a bit nicer to work with and the knots line up more smoothly.
I’ve actually only used the silk for one garment ever, but am going to try to do it more often on my nicer things. I find the cotton holds up well enough to daily wear though, despite being not ideal. The buttonholes are never the first part of my garments to wear out.
I cut a piece of about one arm’s length more or less, depending on the size of buttonhole. For any hole longer than about 4cm I use 2 threads, one to do each side, because the end gets very frayed and scruffy by the time you’ve put it through the fabric that many times.
I wax about 2cm of the tip (Not the entire thread. I wax the outlining/overcasting thread but not the buttonhole thread itself.) to make it stick in the fabric better when I start off the thread.
I don’t tend to tie it, I just do a couple of stabstitches or backstitches and it holds well. (I’m generally very thorough with tying off my threads when it comes to hand sewing, but a buttonhole is basically a long row of knots, so it’s pretty sturdy.)
Put the needle through underneath, with the tip coming up right along that little outline you sewed earlier. And I personally like to take the ends that are already in my hand and wrap them around the tip of the needle like so, but a lot of people loop the other end up around the other way, so here’s a link to a buttonhole video with that method. Try both and see which one you prefer, the resulting knot is the same either way.
Sometimes I can pull the thread from the end near the needle and have the stitch look nice, but often I grab it closer to the base and give it a little wiggle to nestle it into place. This is more necessary with the cotton than it is with the silk.
The knot should be on top of the cut edge of the fabric, not in front of it.
You can put your stitches further apart than I do if you want, they’ll still work if they’ve got little gaps in between them.
Keep going up that edge and when you get to the end you can either flip immediately to the other side and start back down again, or you can do a bar tack. (You can also fan out the stitches around the end if you want, but I don’t like to anymore because I think the rectangular ends look nicer.)
Here’s a bar tack vs. no bar tack sample. They just make it look more sharp, and they reinforce the ends.
For a bar tack to a few long stitches across the entire end.
And then do buttonhole stitches on top of those long stitches. I also like to snag a tiny bit of the fabric underneath.
Then stick the needle down into the fabric right where you ended that last stitch on the corner of the bar tack, so you don’t pull that corner out of shape, and then just go back to making buttonhole stitches down the other side. Then do the second bar tack once you get back to the end.
To finish off my thread I make it sticky with a bit more beeswax, waxing it as close to the fabric as I can get, and then bring it through to the back and pull it underneath the stitches down one side and trim it off.
In my experience it stays put perfectly well this way without tying it off.
Voila! An beautiful buttonholes!
If you want keyhole ones you can clip or punch a little rounded bit at one end of the cut and fan your stitches out around that and only do the bar tack at one end, like I did on my 1830’s dressing gown.
(I won’t do that style in my video though, because they’re not 18th century.)
Do samples before doing them on a garment! Do as many practice ones as you need to, it takes a while for them to get good! Mine did not look this nice 10 years ago.
Your first one will probably look pretty bad, but your hundredth will be much better!
"Mark your line, a bit longer than your button is wide." For people like me who would invariably still not make their buttonholes long enough without more specific instructions: I was taught that buttonholes should be the width of the button plus the thickness of the button
Another thing you can do is wrap a tiny strip of paper around the button so you know exactly how big of a hole it fits through, and then use the length that folded strip of paper to mark the holes.
If I’m uncertain then I’ll stick the button through after the overcasting step!
sinattea replied to your photo “vincentbriggs:I’ve finally learned how to do nice looking 18th century…”
Do you have tutorials or tips on sewing buttonholes?? I always saw mine by hand because I don’t get how the buttonhole foot works. Would love to have them look as even and nice as yours.
Yes, I really should have linked the video I followed when I posted that photo!
I inherited these along with about a dozen other pairs of old scissors, but I only recently learned that they’re for cutting buttonholes, and they’re GREAT!
someone accused me of feigning a sexual attraction to spiders for clout. there's easier ways to get clout, man.....
Someone once called my 22 minute hand sewn 18th century buttonhole tutorial video "Empty, clout driven content" so I think some people will just say anything.
Had a soul-searing moment where I sat unblinking trying to figure out what a "hand sewn 18th century butthole" could be for, until I read that again.
(x)
