Questions tagged [full-bridge]
The full-bridge tag has no summary.
159 questions
-1
votes
0
answers
58
views
Full H bridge Power amplifier failure at higher voltages
I have designed a 4 channel full bridge power amplifier in a PCB using IR2110 driver and FCPF400N80Z MOSFETs. I am applying 200 V to MOSFETs. All 4 channels are exact replicas of each other. 3 of my ...
- 1
0
votes
0
answers
72
views
MOSFET High Side High Voltage Droop
EDIT: My prior question was resolved due to using standard scope probes and not differential probes. It was all about measurement issues. This question is based on the same circuit, but about ...
1
vote
1
answer
76
views
Load Cells - 4x full bridge or 4x half bridge?
After some insight to why 4 half-bridge load cells connected parallelly to one ADC is superior to 4 full-bridge load cells in the same way.
I have been informed that the difference in cost of both ...
- 11
3
votes
1
answer
357
views
About a center-tapped fullwave rectifier understand
Below two paragraph source from The Art of Electronics third edition at page 33.
The circuit in Figure 1.63 is called a center-tapped fullwave
rectifier. The output voltage is half what you get if
...
- 497
1
vote
0
answers
32
views
Derivation of Rac of a Full bridge LLC converter
I'm looking for a way to do dénervation of the Rac (reflected load resistance) of the full bridge LLC converter. See the schematic page 4 and the Rac expression page 5.
Sources :
Full-Bridge LLC ...
- 149
1
vote
2
answers
94
views
How to calculate the maximum horsepower output of a 3-Phase Full-Bridge using a SiC module?
I am trying to estimate the maximum mechanical output power (horsepower) of a 3-phase full-bridge inverter using the Infineon FS05MR12A6MA1B SiC module. The datasheet is available here.
System ...
- 343
4
votes
2
answers
1k
views
What are the advantages of an eight diode 3 phase full bridge rectifier?
I'm replacing my car's alternator, and tearing the old one apart, as you do. The alternator is wired in a Y configuration with 8 diodes, 2 on the neutral point, and then the standard 2 on each of the ...
- 905
0
votes
1
answer
244
views
Amplifying audio on piezo buzzer
I want to output an audio signal from a uC to a piezo buzzer. I first tried the obvious solution with a single transistor in series with the buzzer, but at 3V the sound volume was a bit too low.
The ...
- 1
0
votes
2
answers
133
views
Output Voltage Drop and Insufficient Current Consumption in a Full-Bridge DC/DC Converter
I assembled and tested the circuit shown in the schematic on a copper board. Without any load, I can achieve the desired output voltage of 400V. However, when I connect a 400W load, the output voltage ...
- 123
3
votes
3
answers
1k
views
Strange pulldown resistor behavior with power MOSFET and Full Wave Rectifier in LTSpice
I've been having some trouble getting a pulldown resistor to behave as expected in LTspice. Here are two screenshots of my circuit.
This circuit has a full wave bridge rectifier convert AC (USA ...
- 33
0
votes
1
answer
215
views
Zero Voltage Switching (ZVS) in Conventional Full-Bridge DC/DC Boost Converter
I am trying to design a Conventional Full-Bridge DC/DC Boost Converter with the following parameters (I am not sure if you need them);
Input voltage: 24 V (DC)
Output voltage: 400 V (DC)
Output ...
- 123
2
votes
2
answers
203
views
Output of a stand-alone full wave rectifier is different from the one in the circuit in which it is implemented
I'm trying to simulate an evening lamp using a NE555 timer and a relay.
To do so, I'm stepping down the 230V AC household voltage to 16V by an RC circuit as shown.
Now, when I take a stand-alone ...
- 23
0
votes
3
answers
599
views
Power output of a full bridge diode rectifier
Assume a simple circuit with a 12 V (RMS) AC supply and a 100 ohms load resistor. The power dissipated is P = V^2/R = 1.44 W.
Now assume that a full bridge diode rectifier (without filtering) is ...
- 21
0
votes
0
answers
381
views
How to choose Duty Cycle value for a Full-Bridge DC/DC Converter
I've noticed that while designing DC/DC converters, some sources (at the bottom of the website, comment of Benjamin Lough) suggest a "rule of thumb" duty cycle of 70%, while others (This is ...
- 123
1
vote
0
answers
254
views
Use a pair of half-bridge drivers to make a full-bridge driver
I intend to use a pair of half-bridge drivers and a logic gate to make a full-bridge driver for controlling my DC motors with 3 standard input pins of Enable, Direction, and Arduino PWM.
I looked at a ...
- 31