I would like to configure an embedded device to behave as a wireless router, and I would like to achieve it preferably using networkd configuration files.
I have two *.network files, a wired WAN interface and a wireless LAN interface, and I would like LAN traffic to be able to access WAN.
# cat /etc/systemd/network/wired.network
[Match]
Name=eth0
[Network]
DHCP=ipv4
IPForward=yes
IPMasquerade=yes
As is common for wireless routers, the wireless LAN network anso provides DHCP. I used the systemd integrated DHCP server.
# cat /etc/systemd/network/wireless.network
[Match]
Name=wlan0*
[Network]
Description = Wireless IP interface
DHCPServer= yes
[Address]
Address = 192.168.128.1/24
Broadcast = 192.168.128.255
[DHCPServer]
PoolOffset = 10
PoolSize = 40
EmitDNS = yes
DNS = 8.8.8.8, 8.8.4.4
DefaultLeaseTimeSec = 600
MaxLeaseTimeSec = 7200
[Route]
I assume there should be a NAT between the two networks, as is common for wireless routers, but it is not an explicit requirement.
This is as far as I got with my current knowledge, the wired interface connects to WAN properly, and the wireless access point also provides DHCP addresses. But I am unable to access WAN (internet) if I connect to the WiFi AP.
Here is some network interface status:
# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:26:32:f0:03:21 brd ff:ff:ff:ff:ff:ff
inet 192.168.178.107/24 brd 192.168.178.255 scope global dynamic eth0
valid_lft 4650sec preferred_lft 4650sec
inet6 fe80::226:32ff:fef0:321/64 scope link
valid_lft forever preferred_lft forever
3: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default
link/sit 0.0.0.0 brd 0.0.0.0
4: wlan0wext: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 00:1d:43:40:0d:04 brd ff:ff:ff:ff:ff:ff
inet 192.168.128.1/24 brd 192.168.128.255 scope global wlan0wext
valid_lft forever preferred_lft forever
inet6 fe80::21d:43ff:fe40:d04/64 scope link
valid_lft forever preferred_lft forever
And route status:
# ip route
default via 192.168.178.1 dev eth0 proto dhcp src 192.168.178.107 metric 1024
192.168.128.0/24 dev wlan0wext proto kernel scope link src 192.168.128.1
192.168.178.0/24 dev eth0 proto kernel scope link src 192.168.178.107
192.168.178.1 dev eth0 proto dhcp scope link src 192.168.178.107 metric 1024
# ip route show table local
broadcast 127.0.0.0 dev lo proto kernel scope link src 127.0.0.1
local 127.0.0.0/8 dev lo proto kernel scope host src 127.0.0.1
local 127.0.0.1 dev lo proto kernel scope host src 127.0.0.1
broadcast 127.255.255.255 dev lo proto kernel scope link src 127.0.0.1
broadcast 192.168.128.0 dev wlan0wext proto kernel scope link src 192.168.128.1
local 192.168.128.1 dev wlan0wext proto kernel scope host src 192.168.128.1
broadcast 192.168.128.255 dev wlan0wext proto kernel scope link src 192.168.128.1
broadcast 192.168.178.0 dev eth0 proto kernel scope link src 192.168.178.107
local 192.168.178.107 dev eth0 proto kernel scope host src 192.168.178.107
broadcast 192.168.178.255 dev eth0 proto kernel scope link src 192.168.178.107
I was not able to find many examples for the [Route] section, and I only have the basic understanding of routing.
Regards, Iztok Jeras
